Sanduuqa isgoysyada sawir-maskaxeedku waa isku-xidhaha u dhexeeya xayndaabka unugyada cadceedda oo ka kooban qaybaha unugyada cadceedda iyo qalabka xakamaynta kharashka qoraxda. Waa naqshad dhammaystiran oo iskutallaab ah oo isku dhafan naqshad koronto, naqshad farsamo iyo sayniska agabka.
1. Shuruudaha sanduuqa isgoysyada sawirkavoltaic
Sababo la xiriira gaar ahaan isticmaalka unugyada cadceedda iyo qiimahooda qaaliga ah, sanduuqa isku xirka qoraxda waa inuu lahaadaa sifooyinka soo socda:
1) Waxay leedahay iska caabin wanaagsan oo ka hortagga gabowga iyo UV;
2) Waxaa loo isticmaali karaa jawi adag oo dibadda ah;
3) Waxay leedahay hab aad u fiican oo kuleylka kuleylka ah iyo mugga godka gudaha oo macquul ah si loo yareeyo heerkulka gudaha si loo daboolo shuruudaha badbaadada korantada;
4) Shaqo wanaagsan oo aan biyuhu iyo boodhka ka celin karin.
2. Alaabta kormeerka joogtada ah ee sanduuqa isgoyska
v Tijaabada xidhidhiyaha
v Tijaabada iska caabinta cimilada
v Tijaabada waxqabadka dabka
v Hagaajinta tijaabada waxqabadka cagaha dhamaadka
v Tijaabada isku halaynta ee isku xidhka plug-in
v Ogaanshaha heerkulka isgoyska Diode
v Ogaanshaha iska caabbinta xiriirka
Shayada tijaabada ah ee kor ku xusan, waxaan kugula talineynaa qalabka PPO ee sanduuqa isku xirka jirka / qaybaha daboolka; Qalabka PPO iyo PC ee xirayaasha; PA66 ee looska.
3. Sanduuqa isgoysyada PV jirka / walxaha daboolka
1) Shuruudaha waxqabadka ee sanduuqa isku xirka jirka / daboolka
v Hayso caabbinta gabowga iyo UV wanaagsan;
v Iska caabin weyn oo hoose;
v Waxqabadka dib u dhigista ololka ee heer sare ah;
v Iska caabin kiimiko oo wanaagsan;
v Iska caabbinta saamaynta kala duwan, sida saamaynta qalabka farsamada, iwm.
2) Dhowr arrimood oo lagu talinayo alaabta PPO
v PPO waxay leedahay saamiga ugu yar shanta balaastiig ee injineerinka ah, waana wax aan sun ahayn oo buuxiya heerarka FDA;
v U adkaysiga kulaylka aadka u wanaagsan, oo ka sarreeya PC-ga agabka amorphous;
v Alaabta korantada ee PPO ayaa ah kuwa ugu wanaagsan balaastikada injineerinka guud, iyo heerkulka, qoyaanka iyo inta jeer ee ay saameyn yar ku leeyihiin sifooyinka korantada;
▲PPO/PS waxay leedahay hoos u dhac yar iyo xasillooni cabbir wanaagsan;
▲PPO iyo PPO/PS alwaaxyada taxanaha ah ayaa leh caabbinta biyaha kulul ee ugu fiican ee balaastigga injineerinka guud, heerka nuugista biyaha ugu hooseeya, iyo isbeddel yar oo cabbir ah marka biyaha lagu isticmaalo;
▲ PPO/PA Alloys taxane ah waxay leeyihiin adkeysi wanaagsan, xoog sare, caabin dareere ah, waana la buufin karaa;
v MPPO ololka dib u celisa guud ahaan waxay isticmaashaa fosfooraska iyo nitrogen ololka dib-u-celinta, kuwaas oo leh sifooyinka dab-demiska aan halogen-ka lahayn oo buuxiya jihada horumarinta ee alaabta cagaaran.
3) Astaamaha jireed ee walxaha PPO ee lagu taliyey ee jirka sanduuqa
Phantida | Standard | Shuruudaha | Unug | Tixraac |
Cufnaanta | ASTM D792 | 23℃ | g/cm3 | 1.08 |
Tusmada dhalaalaysa | ASTM D1238 | 275 ℃ / 5KG | g/10 daqiiqo | 35 |
Xoogga Jilicsan | ASTM D638 | 50mm/daqiiqo | Mpa | 60 |
Dheeraynta xilliga nasashada | ASTM D638 | 50mm/daqiiqo | % | 15 |
Xoog dabacsanaan | ASTM D790 | 20mm/daqiiqo | Mpa | 100 |
Hababka dabacsanaanta | ASTM D790 | 20mm/daqiiqo | Mpa | 2450 |
Izod saamaynta xoogga | ASTM D256 | 1/8″,23℃ | J/M | 150 |
Tijaabada iftiinka UV | UL 746C | f 1 | ||
Dusha iska caabinta | IEC 60093 | ohms | 1.0E+16 | |
Iska caabin mugga | IEC 60093 | ohms · cm | 1.0E+16 | |
HDT | ASTM D648 | 1.8 Mpa | ℃ | 120 |
Dab-demiska | UL94 | 0.75 mm | V0 |
4. Walxaha isku xira fiilada
1) Shuruudaha muhiimka ah ee qalabka isku xirka
▲ Hayso wax qabad wanaagsan oo dab-damis ah, iyo shuruudaha dib u dhigista ololku waa UL94 V0
v Xidhiidhiyayaasha guud ahaan waa in la geliyo oo la soo saaraa marar badan, sidaas darteed xoogga iyo adkaanta walxaha ayaa looga baahan yahay inay sare u kacaan;
v Lakabka dahaarka ee dibadda wuxuu leeyahay hawlo ka hortagga gabowga iyo ultraviolet-ka oo aad u wanaagsan, waxaana muddo dheer loo isticmaali karaa deegaan qallafsan.
v Waxqabadka dahaarka (xoogga burburka dahaarka iyo iska caabinta dusha sare) shuruudaha ayaa sarreeya
v Hygroscopicity hooseeya, saamaynta ugu yar ee xasiloonida korantada iyo cabbirka
2) Qalabka jirka ee lagu taliyey xiriyaha fiilada walxaha PPO
Phantida | Standard | Shuruudaha | Unug | Tixraac |
Cufnaanta | ASTM D792 | 23℃ | g/cm3 | 1.09 |
Tusmada dhalaalaysa | ASTM D1238 | 275 ℃ / 5KG | g/10 daqiiqo | 30 |
Xoogga Jilicsan | ASTM D638 | 50mm/daqiiqo | Mpa | 75 |
Dheeraynta xilliga nasashada | ASTM D638 | 50mm/daqiiqo | % | 10 |
Xoog dabacsanaan | ASTM D790 | 20mm/daqiiqo | Mpa | 110 |
Hababka dabacsanaanta | ASTM D790 | 20mm/daqiiqo | Mpa | 2600 |
Izod saamaynta xoogga | ASTM D256 | 1/8″,23℃ | J/M | 190 |
Tijaabada iftiinka UV | UL 746C | f 1 | ||
Dusha iska caabinta | IEC 60093 | ohms | 1.0E+16 | |
Iska caabin mugga | IEC 60093 | ohms · cm | 1.0E+16 | |
HDT | ASTM D648 | 1.8 Mpa | ℃ | 130 |
Dab-demiska | UL94 | 1.0 mm | V0 |
3) Qalabka jirka ee lagu taliyey xiriiriyaha fiilada ee walxaha PC
Phantida | Standard | Shuruudaha | Unug | Tixraac |
Cufnaanta | ASTM D792 | 23℃ | g/cm3 | 1.18 |
Tusmada dhalaalaysa | ASTM D1238 | 275 ℃ / 5KG | g/10 daqiiqo | 15 |
Xoogga Jilicsan | ASTM D638 | 50mm/daqiiqo | Mpa | 60 |
Dheeraynta xilliga nasashada | ASTM D638 | 50mm/daqiiqo | % | 8 |
Xoog dabacsanaan | ASTM D790 | 20mm/daqiiqo | Mpa | 90 |
Hababka dabacsanaanta | ASTM D790 | 20mm/daqiiqo | Mpa | 2200 |
Izod saamaynta xoogga | ASTM D256 | 1/8″,23℃ | J/M | 680 |
Tijaabada iftiinka UV | UL 746C | f 1 | ||
Dusha iska caabinta | IEC 60093 | ohms | 1.0E+16 | |
Iska caabin mugga | IEC 60093 | ohms · cm | 1.0E+16 | |
HDT | ASTM D648 | 1.8 Mpa | ℃ | 128 |
Dab-demiska | UL94 | 1.5 mm | V0 |
5. Walxaha lowska
1) Shuruudaha muhiimka ah ee walxaha lowska
v Shuruudaha dib u dhigista ololka UL 94 V0;
v Waxqabadka dahaarka (xoogga burburka dahaarka iyo iska caabinta dusha sare) shuruudaha ayaa sarreeya;
v Hygroscopicity hooseeya, saameyn yar oo ku saabsan xasilloonida korantada iyo cabbirka;
v Dusha sare, dhalaal wanaagsan.
2) Astaamaha jireed ee looska PA66 ee lagu taliyay
Phantida | Standard | Shuruudaha | Unug | Tixraac |
Cufnaanta | ASTM D792 | 23℃ | g/cm3 | 1.16 |
Tusmada dhalaalaysa | ASTM D1238 | 275 ℃ / 5KG | g/10 daqiiqo | 22 |
Xoogga Jilicsan | ASTM D638 | 50mm/daqiiqo | Mpa | 58 |
Dheeraynta xilliga nasashada | ASTM D638 | 50mm/daqiiqo | % | 120 |
Xoog dabacsanaan | ASTM D790 | 20mm/daqiiqo | Mpa | 90 |
Hababka dabacsanaanta | ASTM D790 | 20mm/daqiiqo | Mpa | 2800 |
Izod saamaynta xoogga | ASTM D256 | 1/8″,23℃ | J/M | 45 |
Tijaabada iftiinka UV | UL 746C | f 1 | ||
Dusha iska caabinta | IEC 60093 | ohms | 1.0E+13 | |
Iska caabin mugga | IEC 60093 | ohms · cm | 1.0E+14 | |
HDT | ASTM D648 | 1.8 Mpa | ℃ | 85 |
Dab-demiska | UL94 | 1.5 mm | V0 |
Waqtiga boostada: 15-09-22